Muhammad Adeel

 I have the necessary skills ,qualities, and experience to carry out the duties to a very high standard. An ability to work as part of a team to achieve the compny goals and projects. High level of customer service and care. Taking responsibility for my ongoing professional development an honest reliable and disciplined approach to my work.A positive and enthusiastic attitude to my work. If  I am successful, I will constantly seek to add value in my work to help your company maintain its position as Technician ,and to ensure you see a positive return from your investment.I am available for an interview at short notice and would very much appreciate the opportunity to demonstrate to you my skills, qualities, and experience.
 

AL BARIO ENGINEERING PVT LIMITED.
(Senior Service Engineer) Dec 2019 up to date.
Troubleshooting’s Maintenance and commissioning of Generators.  
 Engines start up Failure Gas engines and diesel engines with different controller’s Deep sea ComAp Dia ne XT, HMI.
  Fault finding on Actuators, Governors, servomotors, ECM, pick up sensors Power ramp up down, Load sharing’s kw and kvar, power factor. 
 ACB VCB fault finding LT circuit and HT circuit.
 Complete the fault finding on alternator AVR, DVR, PMG, Diode, Veristors.
 Fault finding with excitation systems on generators.
 Troubleshooting on Parallel running engines.
  All Termination of control cables and power cables carried out.
 Removing and installation of all control signal and power harness of gas and diesel engine.
       
Orient Energy system PVT LIMITED 
Duration March 2016 to Dec 2019 (3 years)
(Service Engineer)

 Installation of PLC B&R Input and output module Card.
 Installation of servo drive, Actuators, and calibration, controller PID fine tune. 
 Troubleshooting on PLC and rectify the problems.
 Installation Magnetic Contactors Relays Fuse Breakers. 
  Software installation and setting carried out on AVR, UFRO, droop, PF and DVR BESLLER DECS100 DM 110 ABB Unitrol DVR, configured it and synchronized with multiple engines.  
 overhauling of alternator, Stamford AVK, Leroy somer complete testing with Magar.
 Short circuit test LV AND HT Alternators and power cables.
  Generators ACB, VCB installation and configure controlled on HMI.
 Replacement the DE and NDE Bearing and installed the bearing modification AVK.

AL AMAN MODERN ENERGY KSA. 
Duration (Experience 1 year) Service Engineer.

 Synchronized CAT engines EPMC 4.2 with ComAp Intellivision.
 Installation of synchronization control panel and load sharing module.
 AVR MX 321 and MX341 settings carried out on Stamford alternator
 Adjusting the power factor and resolve the problem on controller PFC3.
 Performed the load sharing control with multiple engines.
 All routine maintenance preventive as per maintenance manual.
 Troubleshooting on Cummins Engines QST 30, PCC 2100, and PCC 3100.
 Troubleshoot portable engines Perkins with power wizard 1.0, 1.2.
 Perkins series 1100,1103,1104,1106 series 2000, 2506,2806 etc.
 Replacement of Head an and head gasket removing of turbocharger, fuel pump and water pump, Radiator fuel tank day tank.
 Caterpillar 3412, C15, C18 engines commissioning and troubleshooting.

    Orient Energy system PVT LIMITED Dec -2009 to July 2015.  6 years
Distributions sales and services of GE Jenbacher Gas and Cummins diesel engines. (Senior service Technician)

 Commission of the Gensets JGS 320, JGS420, JGS 620 and tested at full load.
 Commission of the Diesel Gensets Cummins KTA 19 KTA 50 QXS15 and tested at full load.
 Synchronized the Gas engine and diesel engine with parallel operation and speed mode.
 Configuration of synchronized relays wood word SPMD controlled the gen GCB.
 Read the Electrical diagram and resolve the problem on troubleshooting’s.
 Testing and installations of thermocouples, Pressure sensors, PT 100.and Level switches.
 Work on Engines controllers and adjusted the speed controller’s parameters isolated controller parameters, power controller parameters and lean ox controller’s parameters.
 Works on ignitions systems on gensets JGS 320, JGS 420, JGS 620 And troubleshooting.
 Performed the Insulation test, short circuits test and open circuits test on 1 MW 1.4 MW and 3 MW alternators. 
 Star delta, start stop, DOL circuits.
 Installations of CT and PT and configured in controller.
 Performed 2000 hours 10,000 hours, and 20,000 hours routine Maintenances of GE Jenbacher 
  Assist and Performed top end (30,000 hours) of GE Jenbacher gas engines JGS 320, JGS 420, JGS 620, JMS 612, JMS 616, JMS 620.
 Assist the 60,000 hours’ maintenance of JGS 320 major overhauling.
 Assist on Cummins diesel gensets overhauling in workshop.
Short Trainings:
Jenbacher GE: 
Certified FTA Field Technician Advance from GE.
Certified FTB Field Basic Training from GE
 

:
DAE                  Electrical            PBTE             2008          
Matric     science    BISE 2005